Convert Atmel c code into Arduino MPPT

$30-250 AUD

已关闭

已发布

大约 10 年前

$30-250 AUD

货到付款

Hi there Freelancers I need some Atmel c code converted to work with the Arduino UNO. It is a maximum power point tracking routine. It will need to be well noted so that i can modify it later. If the end result works well there might also be more work available for a later project. The PWM output can be on any pin and should be at around 20 khz The current input will be a 0-5 volt signal and can be on any input pin The voltage input will be a 0-5 volt signal and can be on any input pin The software should be efficient I would also like to add a variable resistor to limit the output at a certain voltage. I have a buck converter board that can be used to test the software. Previous experience with arduino and or maximum power point tracking would be good. Please let me know if you would like to see the example code. Thankyou for your bids!

Arduino

C Programming

Electrical Engineering

Electronics

Microcontroller

项目 ID: 5354566

关于此项目

22提案

远程项目

活跃10 年前

想赚点钱吗？

电子邮箱地址

在Freelancer上竞价的好处

设定您的预算和时间范围

为您的工作获得报酬

简要概述您的提案

免费注册和竞标工作

22威客以平均价$202 AUD来参与此工作竞价

@shahbaz1980

hello, I can provide the arduino sketch, instead of converting existing code i will suggest to write new sketch or i have one working with 48V PV system. if you wish i can send you that. Regards, Shahbaz.

$538 AUD 在15天之内

4.9

(72条评论)

7.1

@designvin

Hello, I have worked on Arduino and MPPT. MPPT was used for my company internal project. Would be great if I can participate in the project. I can also explain what I have done before Thanks Vinod

$155 AUD 在7天之内

5.0

(9条评论)

5.8

@farazahmad759

NOTE: MY RATE IS VERY HIGH, IF YOU CAN'T PAY AS MY BID, PLEASE DON'T READ AHEAD. I DON'T COMPROMISE ON THE QUALITY SO NO COMPROMISE ON THE PRICE!! Dear Hiring Manager, I am a professional electrical engineer and have completed more than 150 projects for local and international clients and have also complete 36 reviews with excellent reviews here in freelancer.com More than 80% of my projects are microcontroller/arduino/zigbee based so I have high programming skills in these platforms. As far as MPPT is concerned, I have programmed 'Perturb and Observe' algorithm for MATLAB, PIC and ATMEL. It's not very difficult for me to write code for arduino. I guarantee you will be 110% satisfied with my work and we will have strong long term relationships for future projects. You just need to write every specifications, and my job will be to deliver you the best code according to your demands. If you are interested, then contact me and discuss the details with me. I provide free 15 days support to my clients even after the work is completed! Best Regards, Faraz Ahmad

$333 AUD 在10天之内

4.9

(48条评论)

5.7

@eried

G'day mate! can I see the code you need to use in the arduino? should this code be "converted" or rebuilt/reinterpreted just to get it replicating the behaviour? (Salute was adapted for Aussies)

$222 AUD 在3天之内

5.0

(31条评论)

5.4

@grrod

Hi micaant. Im Greg. Im Telecommunication engineer. I can help you with your projects. Ive programmed al ot of Arduinos directly from Atmel datasheet. I also own a lot of them. Can i take a look at the code? Is this oriented to some chip (atmega328p) Message me and we can discuss the project. Check out my previous reviews. Regards.Greg.

$400 AUD 在15天之内

5.0

(11条评论)

5.1

@zelamicro

Hi, I have years of experience both with Arduino and separate Atmel microcontrollers. I can give you quality work on time. Thank you.

$150 AUD 在5天之内

4.9

(24条评论)

4.9

@varticartur

Hi there! So, you need to convert an existing C code into Arduino code and if is possible improve it? The code I'll need to see if you'll award the project to me.

$147 AUD 在3天之内

5.0

(4条评论)

3.3

@rappt

Hi, I work with Arduino and i am engineer currently working with that type of projects. Would like to help you. Waiting your reply.

$50 AUD 在3天之内

0.0

(0条评论)

0.0

@hafpop

Hi ! I'd like to see the code. BAsically if you have AVR code it can be very easily 'converted' to Arduino code. Additionally - any issue can arrive I can solve it easily - I have experience of 12 years in AVR and about 3 in Arduino. This is basically same thing BUT it does have some C++ libraries which are exposing a higher level API BR, Horia PS if you need only to make the C AVR source buildable for Arduino UNO the price is only 120 AUD.

$222 AUD 在9天之内

0.0

(0条评论)

2.8

@supermind2002

Hello, I will like to see your C code. I have previous MPPT experience. I am microcontroller programmer from pas 3 years.

$111 AUD 在3天之内

0.0

(0条评论)

0.0

@manimuthukumar

I have more than 12 years of industrial experience in embedded system. I have worked on various projects and developed protocol, system software and Firmware for ARM and Microcontrollers. I have developed ATMGA16 based MPPT algo for Buck converter which controlles the duty cycle of the IGBT ( 30 KHZ) using the Input voltage and the Current as the input . the Algo is based on P& O Method for varying the Duty cycle . I have hadled other hobby project to monitor the humidity and the Temperature of a hot chamber Thanking you

$200 AUD 在3天之内

0.0

(0条评论)

0.0

@Dpereztaylor

I have a patent pending of a peripheral device that I desing using an arduino pro mini, this device will be marketed and distributed soon.

$250 AUD 在7天之内

0.0

(0条评论)

0.0

@littleapp

I'm a new Freelancer but with over 20 years of experience programming embedded systems, mostly in C. I'm also familiar with designing a maximum power point tracking system from my first engineering job, only it was on a power driver for an ultrasonic cleaner and it used only analog electronics (op-amps).

$198 AUD 在7天之内

0.0

(0条评论)

0.0

@SannanFarooq

A proposal has not yet been provided

$155 AUD 在3天之内

0.0

(0条评论)

0.0

@rdbembsys

Hi, I have over 20 year of experience in the field of embedded system design and development, Pl. go through my profile portfolio which gives you better idea of my expertise. look forward next level communication, Thanks With Warm Regards Innovative Embedded System

$277 AUD 在30天之内