Find Jobs
Hire Freelancers

Problem with 74HC4067 multiplexer

$10-30 USD

已关闭
已发布超过 1 年前

$10-30 USD

货到付款
Very weird problem I am investigating. Ch0 to Ch3 - everything is fine Ch4 to Ch11 - doesn’t function Ch12 to Ch15 - works fine, but their values are replicated to every 4th channel backwards; For example - Ch15 high (4095 adc) will show same value (or nearly the same) for Ch11 and Ch7. Ch14 will show same readings for Ch10 and Ch6. Ch13 will show same readings for Ch9 and Ch5. Ch12 will show same readings for Ch8 and Ch4. Help is appreciated.
项目 ID: 34359322

关于此项目

8提案
远程项目
活跃2 年前

想赚点钱吗?

在Freelancer上竞价的好处

设定您的预算和时间范围
为您的工作获得报酬
简要概述您的提案
免费注册和竞标工作
8威客以平均价$24 USD来参与此工作竞价
用户头像
hi, let us discuss ..........................................................................................
$30 USD 在2天之内
4.8 (30条评论)
5.1
5.1
用户头像
Hi There, I am a senior PhD Level Expert and Have more than 5 years of experience in electronics and microcontroller, microprocessor and logic design problems. Just check my profile and share your details. Time and Budget will be discussed. Thanks
$20 USD 在7天之内
4.6 (13条评论)
5.0
5.0
用户头像
Hi, good afternoon, I am an Electronics Engineer, I have worked with the CD74HC4067 CMOS multiplexer in the past, I think that that the problem could be caused by phantom addresses. How are you driving the IC addresses (pins S1-S4)? Please, message me so we can talk about this. Regards,
$20 USD 在1天之内
5.0 (2条评论)
3.2
3.2
用户头像
Hello, can you share the schematic for better understand where is the problem? Thanks
$20 USD 在7天之内
5.0 (1条评论)
2.6
2.6
用户头像
hi.... There seems to be a problem with your firmware. Are you choosing s0,s1,s2,s3 correctly? If they're all correct, let's look at your sketch and discuss it.* Are there any problems with the board? A/D conversion time?...send me message!!! Thanks and regard.
$20 USD 在1天之内
0.0 (0条评论)
0.0
0.0
用户头像
So instead of bidding on your project, i will just give you some suggestions for things to look for. Some are very obvious and simple while others might be a little more non-obvious. 1. First, is this problem limited to only ONE part or are several affected? In other words, the part may be defective. 2. Check the VCC line to see that you aren't applying too much voltage (this particular HC part is rated for 10V max). 3. Make sure that the Analog Inputs =never= exceed the VCC supply voltage. If they do, the analog signals can possibly "bleed" into other input channels causing something like what you describe. 4. Make sure that the VCC and GND wiring is a very SOLID low impedance path (not, for example, tiny little wires). 5. Check that the VCC and GND lines are quiet and noise free and that there is a 0.1uF decoupling capacitor near to the part. This is more important in TTL Logic circuits but is still helpful to eliminate stray noise even in CMOS logic circuits. 6. Verify that the channel select control lines are clean and that none of them are "floating" and make very certain that none of the select lines are shorted to each other. That would also cause some of the things you described (the problem may then also be in the circuit that is driving those lines). 7. Verify that the Enable pin is solidly grounded when the part is in operation.
$50 USD 在7天之内
0.0 (0条评论)
0.0
0.0
用户头像
Hello i have been working with HC Chips for many years i have got that Multiplexer i have got older Version CD4067 and that is the same i can prove you with both datasheets it is the same the CD4067 has working voltages from 3V to 18V and HCMOS version only works from 3V to 6V i can help you fixing your problem i just need the application schematic from you. have a chat with me i i will show you
$20 USD 在2天之内
0.0 (0条评论)
0.0
0.0

关于客户

UNITED KINGDOM的国旗
Leeds, United Kingdom
5.0
33
付款方式已验证
会员自7月 12, 2017起

客户认证

谢谢!我们已通过电子邮件向您发送了索取免费积分的链接。
发送电子邮件时出现问题。请再试一次。
已注册用户 发布工作总数
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
加载预览
授予地理位置权限。
您的登录会话已过期而且您已经登出,请再次登录。