STM32F746G Brightness

Hi i am experienced electronics engineer with more than 11 years of experience in PCB design. i can do it for you. I have worked on same type of project. Please let me know which LCD we need to control Regards

Hello sir/ma, I'm interested in taking this task up for you. I am an Electrical Engineer with a masters degree and I have high proficiency knowledge in FIRMWARE: FPGA firmware in VHDL and Verilog for Altera/Actel/Xilinx FPGAs and SoCs; MCU firmware in C/C++ for ARM, TI, NXP, Atmel, PIC, Arduino; Bluetooth, Bluetooth Low Energy (BLE), and wireless modules programming,, GPS modules, Temperature, Pressure sensors, Metal Detectors, motor drivers, 12V, 24V DC motors, Servo Motors, HC-05 Bluetooth HARDWARE: Schematic capture: Digital, Analog, Power electronics. EDA: Altium Designer. PCB Layout: Altium Designer, 1 - 10 layers; Component selection, BOM generation, Gerber generation, HVAC, LTE system model, Thermal system design, Matlab/ Simulink, Microcontroller, Modeling, optimization, simulation of building energy systems, Arduino and have been working on Industrial Automatics, Prototyping, PCB Design, Development of Electronic systems. Once you share the project, I will have a look & confirm if I can do it. I’m honest, creative and a unique person to carry out your tasks given to me. Leaving your project on our hand is privileged; we'll make sure that the project is done in a perfect way and do our best until you were satisfied. I would love to discuss this project with you and meet your exact requirements. I am confident I can provide you with top-notch materials that will fit your needs. I pride my work on being professional

Hello. Im designing different electronics devices, mostly based on avr, arm MCUs and boards with them like arduino, stm-discovery etc. (autopromotion^)) Hi. What libraries do you use? What ide? Give more info and lets talk. Bid is not final due to lack of detailes for now.

Hello, i have read the details provided..please contact me to discuss more on the project deadline and some other few things

FREELANCER RECOMMENDED ------------------------------------------------------ Can help... I am an Expert... Lets Start! Please start a Discussion with me and we can get started from there... Please check the past projects I have handled and check my reviews for what employers have to say about my work... Can start right now...

Hello! Nice to meet you! I have read your project carefully. I am very interested in your project. I am a Microelectronics and Automation engineering expert. I have a lot of experience on ARM, FPGA, DSP, Arduino, Raspberry, PLC, PIC, ATMega and so on. And I can code the Python, C/C++, C#, Mobile App. I can do help you. I hope to cooperate with you. Tell me your opinion. My regards.

Hello Dear. I'm designing LOTS of Electronic Devices mostly based on FPGA using Verilog, VHDL. In addition, in terms of ATmega, ARM(mostly STM32F series), PIC programs I have more than 10 years experience. My specialty also lies on Robot Controlling including Kobuki and so on. I am a hardworker having good delivery. You will feel always gorgeous about your project's going if you hire me. EVEN super gorgeous after finishing it.

Hello, I am familiar with this problem, It would be very easy to use timer and GPIO to control and generate needed frequency. This would be very easy if you are already using STM library and drivers. I would be glad to help you in this topic

Hi! I can do your projects . Looking forward for your positive response. Thanks. message me for discussion

Hi there I have experience designing Outdoor panels for digital signage, I have done designs to control LCD Backlights of 2500 nit. With TFT panels of 46, 55 and 65 inch (panels of 60 and 120 Hz) . Therefore, I have considerable experience to help you with your project. Regards Yohan Borda

Dear Sir, We have 10 years of experience in PCB, Schematic and Circuit designs. We ensure that we will finish the project in time with quality. upon your interest We will share you the details of our work. Our capabilities are: - Product design from Concept to Manufacturing - 3D/2D drawing for Concept design - Fusion 360 CAD for Product design - Schematics circuit design and Multilayer PCB Design - Embedded platforms - Arduino/Microcontrollers - In-house Single Layer PCB manufacturing, assembling, and prototyping (low volume)